Model 8T19-M25

Dimensional Drawing

Print / download 8T19-M25 dimensional drawing (PDF).

View I-Beam Flange Width Chart for Wallace Gantries.

Model 8T19-M25

Parts List

Note: There are alternate v-groove casters available for this crane.

Print / download a copy of the 8T19-M25 parts list  (PDF).

Model 8T19-M25

Parts Location Diagrams

Square-Tube Tri-Adjustable I-Beam Assembly Parts Location Diagram

Square-Tube Tri-Adjustable Caster Frame Assembly Parts Location

Print / download a copy of both parts location diagrams (PDF).

Model 8T19-M25

Optional Accessories

Kart Kit for Tri-Adjustable Gantry Cranes

Available accessories include manual and electric trolleys and hoists, jack kits for frequent crane height adjustments, kart kits for transforming your disassembled crane into a cart which allows for easy transport and storage, and festooning kits to keep hoist, trolley, and power drive system cords up and out of the way.

Options for track mounting with V-groove casters and motorizing cranes are also available.

Model 8T19-M25

Assembly and Disassembly Instructions

Cautions

1. Read and understand instructions before using this gantry.
2. Inspect gantry thoroughly before using. See the Tri-Adjustable Operating, Adjustment, and Inspection Instructions (Form 379) for damaged or missing parts.
3. Do not lift more than rated capacity.
4. Center hoist over the load.
5. Do not allow the load to swing or roll against any supporting members.
6. When moving the gantry under load, push on the gantry, not the load. Be certain that the rolling surface is hard, level, clean, and smooth.
7. Do not move the gantry over 50 feet per minute (1/2 m.p.h.).
8. Not to be used for lifting or supporting humans.

Before You Begin

1. Place parts on a flat surface, preferably on cardboard to keep small parts clean and organized.
2. Select a clear area to assemble the crane. The work envelope should extend five feet beyond twice the leg length (when flat) and the length of the I-beam.
3. This clear area should be serviced by two overhead hoists or an alternate as shown below as well as in Form 379. This will allow you to raise the I-beam and leg assemblies when required.
   
   
   
   
   
4. Select tools for fastening the nuts and bolts.
5. You will also need C-clamps to hold the trolley in place while the crane is assembled.

Print / download a PDF of detailed, step-by-step Tri-Adjustable Gantry Crane Square-Tube Assembly Instructions (Form 411).

Model 8T19-M25

Safety Tag and Label Locations

Safety Tag Location

The following sketch shows the location of required safety tags on Wallace 8 and 10-ton steel Tri-Adjustable Gantry Cranes. All locking pins or pins with a quick release must have a corresponding Tag 1969.

Print / download a PDF of the Tri-Adjustable 8 and 10-ton square-tube Safety Tag and Label Locations Diagram and caution labels.

Model 8T19-M25

Inspection Checklist (Form 504)

Instructions include:

• What to check for.
• How often to check.
• Frequent Inspection Checklist.
• Periodic Inspection Checklist.

View detailed Gantry Crane Inspection Checklist (Form 504).

Print / download a PDF copy of the checklist.

If you have questions or need assistance, please contact us.

Disclaimer

Please note this checklist was derived from company proprietary materials and (3) source documents including ANSI B30.17, CMAA Specification #74 Revised 1987, and OSHA 1910.179. As excerpts, the short form Wallace documents are intended to serve as general guidelines and are not to be considered the sole source when performing routine maintenance and inspection tasks.

Model 8T19-M25

Operating, Adjustment, and Inspection Instructions (Form 379)

Instructions include:

• Assembly and Safety Instructions
  • Daily inspection
  • Positioning of Crane to Handle Loads
  • Positioning of Casters
• Adjustment Instructions
  • Height Adjustment Procedure
  • Caster Frame Adjustment Procedure
  • Cantilever Configuration / Adjustment
• Wallace Built-In Safety Features
• Caution Areas
• Tri-Adjustable Visual Checkpoints
• General Safety Instructions for Crane Adjustments
• Methods of Supporting the Crane for Assembly

View detailed Tri-Adjustable Operating, Adjustment, and Inspection Instructions (Form 379).

Print / download a PDF copy of the instructions.

Model 8T19-M25

Cantilever Instructions

Cantilever Chart

Proper Cantilever Procedures

Required counterweight should not be supported by gantry caster frame.

Load and trolley should be able to freely traverse the I-beam through the main legs and brace legs of the gantry.

Print / download a PDF copy of these 8T19-M25 cantilever instructions.

Model 8T19-M25

Warranty and Disclaimer

Wallace product warranty and errors and omissions disclaimers can be found below.

• Product Warranty
• Errors and Omissions Disclaimer

They are also in the About section of this website.

Model 8T19-M25

Engineering Specification

Gantry end frames shall be of steel square tube construction manufactured to Wallace Cranes standards including, but not limited to, the following:

• Gantry shall be adjustable in height and have main leg ductile iron center castings for brace leg attachment to main support legs.
• Gantry shall be adjustable in span so that operators may adjust the crane to an inboard braced, outboard braced, or a combination of the two or approved cantilevered configuration.
• Gantry shall be adjustable in caster frame spread and have ductile iron castings for attachment of casters.
• The steel I-beam shall be American Standard and have a design deflection of no greater than l/800th of the span. The I-beam shall also be free-swinging and self-aligning to lift off-center loads as approved.
• The telescoping legs shall be adjustable in 6” increments and also be equipped with steel safety stop pins for everyday use as well as when adjusting height.
• Spread adjustment on the caster frames shall be in 6” increments. Over spreading of the caster frame adjustment shall be prevented by means of an internal steel safety cable.
• The main leg ductile iron center castings shall have spring-loaded load-bearing adjusting pins for adjusting/maintaining height adjustment of crane as well as attachment of brace legs.
• Gantry shall be equipped with eight, 360 degree rotating, polyurethane casters with 4-position swivel locks, at 90 degrees, to provide easy steering of crane by locking “lead” casters only, or to allow positioning of crane more firmly than a brake by locking all eight casters 90 degrees to each other. Casters shall be 10” diameter.
• The I-beam and I-beam brackets shall be painted with red gloss industrial quality paint.
• The frames, including brace legs, caster frames, and main legs shall be dip painted with red gloss industrial quality paint for protection of both inner and outer tubing walls.
• The model number to be provided shall be tested in accordance with Wallace specifications (A specific unit shipped is not tested; unless a Certificate of Test is ordered [additional charge applies]).
• Gantry is manufactured in accordance with our interpretation of ANSI B30.17 and U.S. OSHA, (Section 1910.179, revised January 1976), regulations at the time of manufacture.

Print / download a PDF version of the specification.

Model 8T19-M25

Photo Gallery

Wallace Tri-Adjustable gantry cranes have a wide variety of commercial and industrial applications, both indoors and out. Images (below) provide a sampling of different applications of our steel (red) and aluminum (silver) Tri-Adjustable gantry cranes.