Model 15T24-20

Dimensional Drawing

– COMING SOON – 

View I-Beam Flange Width Chart for Wallace Gantries.

Model 15T24-20

Parts List

Note: We strongly recommend you consider adding a Power Drive unit for applications where you need to move the crane.

Print / download a copy of the Model 15T24-20 parts list (PDF).

Model 15T24-20

Parts Location Diagrams

Square-Tube Made-to-Order 15-Ton I-Beam Assembly Parts Location Diagram. Click to enlarge.

Square-Tube Made-to-Order 15-Ton Caster Frame Assembly Parts Location Diagram. Click to enlarge.

Print / download a copy of the Model 15T24-20 parts list and parts location diagram (PDF).

Model 15T24-20

Optional Accessories

Sample Trolleys and Hoists Available for Wallace Made-to-Order 15-Ton Gantry Cranes

Available accessories include manual and electric trolleys and hoists as well as festooning kits to keep hoist, trolley, and power drive system cords up and out of the way.

Options for mounting on an angle-iron track with V-groove casters and motorizing cranes with a power drive kit are also available.

Model 15T24-20

Assembly and Disassembly Instructions

Cautions

1. Read and understand instructions before using this gantry.
2. Inspect gantry thoroughly before using (see Form 379F) for damaged or missing parts.
3. Do not lift more than rated capacity.
4. Center hoist over the load.
5. Do not allow load to swing or to roll against any supporting members.
6. When moving gantry under load, push on the gantry, not the load. Be certain that rolling surface is hard, level, clean and smooth.
7. Do not move gantry over 50 feet per minute (1/2 mph).
8. Not to be used for lifting or supporting humans.

Before You Begin

1. Select a clear area to assemble the crane. The work envelope should extend five feet beyond twice the leg length (when flat) and the length of the I-beam.
2. This clear area should be serviced by two overhead hoists or an alternate as shown in Form 379F. The cranes will raise the I-beam and leg assemblies when required.
3. Select tools for fastening the nuts and bolts. You will also need C-clamps to hold the trolley in place while the crane is assembled.
4. Place parts on a flat surface, preferably on cardboard, to keep small parts clean and organized.

Please print / download a PDF of the Made-to-Order 15-Ton Crane Assembly Instructions or Form 15T (184 KB) for detailed, step-by-step instructions.

Model 15T24-20

Inspection Checklist (Form 504)

Instructions include:

• What to check for.
• How often to check.
• Frequent Inspection Checklist.
• Periodic Inspection Checklist.

View detailed Gantry Crane Inspection Checklist (Form 504).

Print / download a PDF copy of the checklist.

If you have questions or need assistance, please contact us.

Disclaimer

Please note this checklist was derived from company proprietary materials and (3) source documents including ANSI B30.17, CMAA Specification #74 Revised 1987, and OSHA 1910.179. As excerpts, the short form Wallace documents are intended to serve as general guidelines and are not to be considered the sole source when performing routine maintenance and inspection tasks.

Model 15T24-20

Operating, Adjustment, and Inspection Instructions (Form 379F)

Instructions include:

• Inspecting Crane Before Moving and/or Each Day’s Use
• Positioning of Crane to Handle Loads
• Positioning of Casters
• Visual Checkpoints
• General Safety Instructions for Crane Adjustments
• Methods for Supporting Crane for Assembly
• Inspection Checklist (Form 504)

View detailed Wallace Fixed Height Gantry Cranes Operating, Adjustment, and Inspection Instructions (Form 379F).

Print / download a PDF copy of the instructions (271 KB).

Model 15T24-20

Warranty and Disclaimer

Wallace product warranty and errors and omissions disclaimers can be found below.

• Product Warranty
• Errors and Omissions Disclaimer

They are also in the About section of this website and on the main Made-to-Order Steel 15-Ton Gantry Cranes page.

Model 15T24-20

Engineering Specification

Gantry end frames shall be of steel square tube construction manufactured to Wallace Cranes standards including, but not limited to, the following:

• Gantry shall be fixed in height and tread.
• Gantry shall be adjustable in span so that operators may adjust the crane to an approved configuration.
• I-beam shall be American Standard with a design deflection of no greater than 1/800th of the span in accordance with Wallace design criteria. I-beam shall be free swinging and self-aligning to allow lifting off-center loads.
• Gantry shall be equipped with four v-groove casters for use on Wallace inverted angle iron track. Casters shall be 10” or 12” diameter as determined by crane type (push or powered).
• The model number to be provided shall be tested in accordance with Wallace specifications (A specific unit shipped is not tested; unless a Certificate of Test is ordered [additional charge applies]).
• The I-beam and I-beam brackets shall be painted with red gloss industrial quality paint.
• The frames including brace legs, caster frames and main legs shall be dip painted with red gloss industrial quality paint
  for protection of both inner and outer tubing walls.
• Gantry is manufactured in accordance with our interpretation of ANSI B30.17 and U.S. OSHA, (Section 1910.179, revised January 1976), regulations at the time of manufacture.

Print / download a PDF version of the specification.